View MPSA55_224743.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MPSA55 / MMBTA55 / PZTA55
MPSA55
MMBTA55
C
PZTA55
C
E C B
TO-92
E
SOT-23
Mark: 2H
B
SOT-223
B
C
E
PNP General Purpose Amplifier
This device is designed for general purpose amplifier applications at collector currents to 300 mA. Sourced from Process 73. See MPSA56 for characteristics.
Absolute Maximum Ratings*
Symbol
VCES VCBO VEBO IC TJ, Tstg Collector-Base Voltage Emitter-Base Voltage Collector Current - Continuous
TA = 25C unless otherwise noted
Parameter
Collector-Emitter Voltage
Value
60 60 4.0 500 -55 to +150
Units
V V V mA C
Operating and Storage Junction Temperature Range
*These ratings are limiting values above which the serviceability of any semiconductor device may be impaired.
NOTES: 1) These ratings are based on a maximum junction temperature of 150 degrees C. 2) These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations.
Thermal Characteristics
Symbol
PD RJC RJA
TA = 25C unless otherwise noted
Characteristic
Total Device Dissipation Derate above 25C Thermal Resistance, Junction to Case Thermal Resistance, Junction to Ambient MPSA55 625 5.0 83.3 200
Max
*MMBTA55 350 2.8 357 **PZTA55 1,000 8.0 125
Units
mW mW/C C/W C/W
*Device mounted on FR-4 PCB 1.6" X 1.6" X 0.06." **Device mounted on FR-4 PCB 36 mm X 18 mm X 1.5 mm; mounting pad for the collector lead min. 6 cm2.
a 1997 Fairchild Semiconductor Corporation
MPSA55/MMBTA55/PZTA55, Rev A
MPSA55 / MMBTA55 / PZTA55
PNP General Purpose Amplifier Electrical Characteristics
Symbol Parameter
TA = 25C unless otherwise noted
(continued)
Test Conditions
Min
Max
Units
OFF CHARACTERISTICS
V(BR)CEO V(BR)CBO V(BR)EBO ICEO ICBO Collector-Emitter Breakdown Voltage* Collector-Base Breakdown Voltage Emitter-Base Breakdown Voltage Collector-Cutoff Current Collector-Cutoff Current IC = 1.0 mA, IB = 0 IC = 100 A, IE = 0 IE = 100 A, IC = 0 VCE = 60 V, IB = 0 VCB = 60 V, IE = 0 60 60 4.0 0.1 0.1 V V V A A
ON CHARACTERISTICS
hFE VCE(sat) VBE(on) DC Current Gain Collector-Emitter Saturation Voltage Base-Emitter On Voltage IC = 10 mA, VCE = 1.0 V IC = 100 mA, VCE = 1.0 V IC = 100 mA, IB = 10 mA IC = 100 mA, VCE = 1.0 V 100 100 0.25 1.2 V V
SMALL SIGNAL CHARACTERISTICS
fT Current Gain - Bandwidth Product IC = 100 mA, VCE = 1.0 V, f = 100 MHz 50 MHz
*Pulse Test: Pulse Width 300 ms, Duty Cycle 2.0%
TO-92 Tape and Reel Data
TO-92 Packaging Configuration: Figure 1.0
Packaging Description:
TO-92 parts are shipped normally in tape. These reeled parts in standard option are shipped with 2,000 units per 14" or 355.6cm diameter reel. This and some other options are further described in the Packaging Information table.These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains one reel maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped.
1 Reel per Inner box
FKS Label
395mm x 375mm x 56mm Inner box(2,000cap)
FKS Label
TO-92 Packaging Configuration: Figure 2.0
Inner Box Bar Code Label Sample
TO-92 Packaging Information Packaging Option Packaging type Qty per Reel/Tube/ Bag Reel Size Inner Box Dimension (mm) Max qty per Box Standard Standard Standard (no flow code) (no flow code) (no flow code) TNR AMMO BULK 2,000 14" Dia 395x375x56 2,000 328x162x43 2,000 1,000 237x167x96 10,000 LOT: TKLEE777 Q'TY: 1000 W/W: 0103 OPTION: 20000025
MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X
P
ETC:
00 / 03 / 17 06:30
DVC:
KA7812-AE
01 01
Outer Box Dimension (mm) 420x420x320 525x360x265 525x360x265 Max qty per Box Weight per unit (gm) Note/Comments 10,000 0.2080 30,000 0.2080 100,000 0.2080 DVC: LOT: Q'TY: KA7812-AE IMSYS777 12000 IM
420mm x 420mm x 320mm Outer box(10,000cap) FKS Label
Outer Box Bar Code Label Sample
00 / 03 / 17 07:30 01
TO-92 AMMO Packaging Configuration: Figure 3.0
88706892 A710103105
7103
15 Ammo boxes per Outer Box 328mm x 162mm x 43mm Inner box (2,000cap) FKS Label FKS Label
525mm x 360m x 265mm Outer box (30,000cap)
TO-92 Bulk Packing Configuration: Figure 4.0
FKS Label
10 Vinyl bags per Inner box 1,000 units per Bulk Vinyl bag 237mm x 167mm x 96mm Bulk Inner box(10,000cap) FKS Label 525mm x 360mm x 265mm Outer box(100,000cap)
(c)2001 Fairchild Semiconductor Corporation
October 2001, Rev. A
TO-92 Tape and Reel Data, continued
TO-92 Reeling Style Configuration: Figure 5.0
Standard
Machine Option
TO-92 Radial Ammo Packaging Configuration: Figure 6.0
Standard
FIRST WIRE OFF IS EMITTER ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON BOTTOM
Machine Option
FIRST WIRE OFF IS COLLECTOR ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON TOP
FIRST WIRE OFF IS COLLECTOR ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON TOP
FIRST WIRE OFF IS EMITTER ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON BOTTOM
October 2001, Rev. A
TO-92 Tape and Reel Data, continued
TO-92 Tape and Reel Taping Dimension Configuration: Figure 7.0
A1 P
T jh
A
H1 H HO
d J1
W2
WO W1 W
P1 F1 P2
F2 DO ITEM DESCRIPTION PO Body Width Body Height Body Thickness Lead-Wire Diameter Pitch of Component Feed Hole Pitch Hole Center to Component Center Lead to Lead Distance Component Alignment F-R Tape Width Hole-Down Tape Width Hole Position Hole-Down Tape Position Height of Component From Tape Center Lead-Wire Clinch Height Component Height Lead-Wire (Tape Portion) Feed Hole Diameter Total Tape Thickness
t
SYMBOL A1 A T d P P0 P2 F1,F2 jh W W0 W1 W2 H H0 H1 J1 D0 t P1
DIMENSION 4.58 (+ 0.25, - 0.15) 4.58 (+/- 0.20) 3.86 (max) 0.46 (+/- 0.05) 12.7 (+/- 0.50) 12.7 (+/ -0.20) 6.35 (+/- 0.50) 2.50 (+ 0.3, - 0.10) 0.00 (+/- 1.00) 18.00 (+ 1.00, - 0.50) 6.00 (+/- 0.50) 9.00 (+/ -0.50) 1.00 (max) 19.50 (+/- 1.00) 16.00 (+/- 0.50) 27.0 (max) 2.50 (min) 4.00 (+/- 0.20) 0.65 (+/- 0.20) 3.85 (+/- 0.50)
REMARK
User Direction of Feed
In Case of Reel Package +/- 1.00 F1-F2= +/- 0.30
H + A <= H1
TO-92 Reel Configuration: Figure 8.0
Position of Hole
Note : All dimensions are in millimeters.
ELECTROSTATIC SENSITIVE DEV ICES
D4
D1
ITEM DESCRIPTION
SYSMBOL
MINIMUM
MAXIMUM
Reel Diameter
D2
D1 D2 D2 D3 D4 W1 W2 W3
13.975 1.160 0.650 3.100 2.700 0.370 1.630
14.025 1.200 0.700 3.300 3.100 0.570 1.690 2.090
Arbor Hole Diameter (Standard) (Small Hole)
FKS Label
Core Diameter Hub Recess Inner Diameter Hub Recess Depth Flange to Flange Inner Width
W1
Hub to Hub Center Width
W3
W2
Note: All dimensions are inches
October 2001, Rev. A
TO-92 Package Dimensions
TO-92 (FS PKG CODE AM)
4.58 -0.15
+0.25
14.47 0.40
0.46 0.10
4.58 0.20
1.27TYP [1.27 0.20] 3.60 0.20 3.86MAX
1.27TYP [1.27 0.20]
0.38 -0.05
+0.10
1.02 0.10
0.38 -0.05
+0.10
(R2.29)
(0.25)
Dimensions in Millimeters
August 1999, Rev B
SOT-23 Tape and Reel Data
SOT-23 Packaging Configuration: Figure 1.0
Packaging Description:
SOT-23 parts are shipped in tape. The carrier tape is made from a dissipative (carbon filled) polycarbonate resin. The cover tape is a multilayer film (Heat Activated Adhesive in nature) primarily composed of polyester film, adhesive layer, sealant, and anti-static sprayed agent. These reeled parts in standard option are shipped with 3,000 units per 7" or 17.7cm diameter reel. The reels are clear in color and is made of polystyrene plastic (anti-static coated). This and some other options are further described in the Packaging Information table. These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains five reels maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped.
Antistatic Cover Tape
Static Dissipative Embossed Carrier Tape
FKS Label
7H
7H
7H
7H Pin 1
SOT-23 Unit Orientation
SOT-23 Packaging Information Packaging Option Packaging type Qty per Reel/Tube/Bag Reel Size Inner Box Dimension (mm) Max qty per Box Standard TNR 3,000 7" Dia 188x181x69 15,000
5 Reels per box
Outer Box Dimension (mm) 420x420x320 Max qty per Box Weight per unit (gm) Weight per Reel (kg) Note/Comments 180,000 0.0084 -
FKS Label
188mm x 181mm x 69mm Inner box(15,000cap)
Inner Box Barcode Label Sample
MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X
Outer Box Barcode Label Sample
00 / 03 / 17 07:30 DVC: LOT: Q'TY: KA7812-AE IMSYS777 12000 IM 01
P
ETC:
00 / 03 / 17 06:30
DVC:
KA7812-AE
01
LOT: TKLEE777 Q'TY: 1000 W/W: 0103 OPTION: 20000025
A710103105
88706892
7103
FKS Label
SOT-23 Tape Leader and Trailer Configuration: Figure 2.0
420m x 420mm x 320mm Outer box(180,000cap)
Carrier Tape Cover Tape
Trailer Tape 640mm minimum or 80 empty pockets
Components
Leader Tape 1680mm minimum or 210 empty pockets
(c)2001 Fairchild Semiconductor Corporation
October 2001, Rev. A
SOT-23 Tape and Reel Data, continued
SOT-23 Embossed Carrier Tape Configuration: Figure 3.0
P0 T E1 P2 D0 D1
F E2 B0 Wc
W
Tc K0
P1
A0
User Direction of Feed
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481 rotational and lateral movement requirements (see sketches A, B, and C).
20 deg maximum Typical component cavity center line 0.5mm maximum
B0 20 deg maximum component rotation
0.5mm maximum
Sketch A (Side or Front Sectional View)
Component Rotation
A0 Sketch B (Top View)
Typical component center line
Sketch C (Top View)
Component lateral movement
Component Rotation
SOT-23 Reel Configuration: Figure 4.0
W1 Measured at Hub
B Min Dim C Dim A max Dim N Dim D min
DETAIL AA
See detail AA W3
7" Diameter Option
W2 max Measured at Hub
Dimensions are in inches and millimeters
Tape Size
8.0mm
Reel Option
7" Dia
Dim A
7.00 177.8
Dim B
0.059 1.5
Dim C
0.512 +0.020/-0.008 13 +0.5/-0.2
Dim D
0.795 20.2
Dim N
2.165 55
Dim W1
0.331 +0.059/-0.000 8.4 +1.5/0
Dim W2
0.567 14.4
Dim W3 (LSL-USL)
0.311 - 0.429 7.9 - 10.9
October 2001, Rev. A
SOT-23 Package Dimensions
SOT-23 (FS PKG CODE AU)
0.20 MIN 2.40 0.10
0.40 0.03
1.30 0.10
0.45~0.60
0.03~0.10 0.38 REF
0.40 0.03 0.96~1.14 2.90 0.10
0.12 -0.023
+0.05
0.95 0.03 0.95 0.03 1.90 0.03 0.508REF
0.97REF
Dimensions in Millimeters
August 1999, Rev B
SOT-223 Tape and Reel Data
SOT-223 Packaging Configuration: Figure 1.0
Packaging Description:
SOT-223 parts are shipped in tape. The carrier tape is made from a dissipative (carbon filled) polycarbonate resin. The cover tape is a multilayer film (Heat Activated Adhesive in nature) primarily composed of polyester film, adhesive layer, sealant, and anti-static sprayed agent. These reeled parts in standard option are shipped with 4000 units per 13" or 330cm diameter reel. The reels are dark blue or black in color and is made of polystyrene plastic (anti-static coated). This and some other options are further described in the Packaging Information table.These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains four reels maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped.
Antistatic Cover Tape
Static Dissipative Embossed Carrier Tape
FKS Label
F T0133 FQT13N60
F T0133 FQT13N60
F T0133 FQT13N60
F T0133 FQT13N60
SOT-223 Unit Orientation
SOT-223 Packaging Information Packaging Option Packaging type Qty per Reel/Tube/Bag Reel Size Inner Box Dimension (mm) Max qty per Box Outer Box Dimension (mm) Max qty per Box Weight per unit (gm) Weight per Reel(kg) Note/Comments Standard TNR 4,000 13" Dia 339x352x68 16,000 420x420x320 64,000 0.1118 -
4 Reels per box
FKS Label 339mm x 352mm x 68mm Inner box(16,000cap)
Inner Box Barcode Label Sample
MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X
Outer Box Barcode Label Sample
00 / 03 / 17 07:30 DVC: LOT: Q'TY: KA7812-AE IMSYS777 12000 IM 01
P
ETC:
00 / 03 / 17 06:30
DVC:
KA7812-AE
01
LOT: TKLEE777 Q'TY: 1000 W/W: 0103 OPTION: 20000025
A710103105
88706892
7103
FKS Label 420mm x 420mm x 320mm Outer box(64,000cap)
SOT-223 Tape Leader and Trailer Configuration: Figure 2.0
Carrier Tape Cover Tape
Trailer Tape 360mm minimum or 45 empty pockets
Components
Leader Tape 1520mm minimum or 190 empty pockets
(c)2001 Fairchild Semiconductor Corporation
October 2001, Rev. A
SOT-223 Tape and Reel Data, continued
SOT-223 Embossed Carrier Tape Configuration: Figure 3.0
P0 T E1 D0
F K0 Wc B0 E2 W
Tc A0 P1 D1
User Direction of Feed
Dimensions are in millimeter Pkg type SOT-223 (12mm)
A0
6.83 +/-0.10
B0
7.42 +/-0.10
W
12.0 +/-0.2
D0
1.55 +/-0.05
D1
1.50 +/-0.10
E1
1.75 +/-0.10
E2
10.25 min
F
5.50 +/-0.05
P1
8.0 +/-0.1
P0
4.0 +/-0.1
K0
1.80 +/-0.10
T
0.30 +/-0.05
Wc
9.50 +/-0.1
Tc
0.10 max
Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481 rotational and lateral movement requirements (see sketches A, B, and C).
20 deg maximum Typical component cavity center line
0.5mm maximum
B0 20 deg maximum component rotation
0.5mm maximum
Sketch A (Side or Front Sectional View)
Component Rotation
A0 Sketch B (Top View)
Typical component center line
Sketch C (Top View)
Component lateral movement
Component Rotation
SOT-223 Reel Configuration: Figure 4.0
W1 Measured at Hub
B Min Dim C Dim A max
Dim N
Dim D min
DETAIL AA See detail AA W3
13" Diameter Option
W2 max Measured at Hub
Dimensions are in inches and millimeters
Tape Size
12.0mm
Reel Option
13" Dia
Dim A
13.00 330
Dim B
0.059 1.5
Dim C
0.512 +0.020/-0.008 13 +0.5/-0.2
Dim D
0.795 20.2
Dim N
4.00 100
Dim W1
0.488 +0.078/-0.000 12.4 +2/0
Dim W2
0.724 18.4
Dim W3 (LSL-USL)
0.468 - 0.606 11.9 - 15.4
October 2001, Rev. A
SOT-223 Package Dimensions
SOT-223 (FS PKG CODE AV)
0.08MAX MAX1.80 1.75 0.20 3.50 0.20 (0.60)
3.00 0.10
0.65 0.20
+0.04
0.06 -0.02
2.30 TYP (0.95) 4.60 0.25
0.70 0.10 (0.95) 0.25 -0.05
+0.10
(0.60)
0~
10
1.60 0.20
(0.46)
(0.89)
6.50 0.20
Dimensions in Millimeters
August 1999, Rev B
7.00 0.30
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.
ACExTM BottomlessTM CoolFETTM CROSSVOLTTM DenseTrenchTM DOMETM EcoSPARKTM E2CMOSTM EnSignaTM FACTTM FACT Quiet SeriesTM
DISCLAIMER
FAST (R) FASTrTM FRFETTM GlobalOptoisolatorTM GTOTM HiSeCTM ISOPLANARTM LittleFETTM MicroFETTM MicroPakTM MICROWIRETM
OPTOLOGICTM OPTOPLANARTM PACMANTM POPTM Power247TM PowerTrench (R) QFETTM QSTM QT OptoelectronicsTM Quiet SeriesTM SILENT SWITCHER (R)
SMART STARTTM STAR*POWERTM StealthTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SyncFETTM TinyLogicTM TruTranslationTM UHCTM UltraFET (R)
VCXTM
STAR*POWER is used under license
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or 2. A critical component is any component of a life systems which, (a) are intended for surgical implant into support device or system whose failure to perform can the body, or (b) support or sustain life, or (c) whose be reasonably expected to cause the failure of the life failure to perform when properly used in accordance support device or system, or to affect its safety or with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
Preliminary
First Production
No Identification Needed
Full Production
Obsolete
Not In Production
This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.
Rev. H4

▲Up To Search▲

Price & Availability of MPSA55

	To Download MPSA55 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .